1/6/2024 0 Comments Mail tabberTo go any thicker would definitely be an adjustment to the machines peel value. The machine applies tabs to 1,2 and 3 page sets in about the same manner. The thickness of the stock can be a consideration. Ideally, the tab should be around 2/3 peeled, but as much as 7/8 may be necessary, depending on the stock that is being ran (8 x 11, 8 x 14, 3 x 5 etc.). There is only one adjustment that can be made electronically this is in regard to how much of the tab is peeled off the peel bar each time. Reduces cost of mailings by eliminating the need for envelopes. Phone: 877.336.6877 Visit: SpecificationsSeals mail pieces with an adhesive tab to create mailings that comply with U.S. If you have any questions or concerns, contact a customer service representative today. OPTIONS: Available in standard or wide head configuration.TAB PLACEMENT Accuracy: +/- 1/8 Inch repeatability.Label/Tab Length: 0.75 Inch (19 mm) to 7 Inch (178 mm).75 Inch (19 mm) to 4.5 Inch (114 mm) for wide head Backer: 0.75 Inch (19 mm) to 2 Inch (50.8 mm) for standard head /.Roll Size: Up to 19.5 Inch (495 mm) diameter mounted on a 3 Inch (76 mm) core, up to 50,000 3/4 Inch (19 mm) tabs or 40,000 1 Inch (25 mm) tabs.Note: Clear and translucent tabs require an “engineered backer” with registration marks for indexing.TABS/LABELS Types: Tabs (single, double, triple), wafer seals, labels, stamps, repositionable notes, customized stickers, scratch-offs, machine grade paper and adhesive, clear, translucent, unperforated, vertical perforated.Thickness: Minimum: 20# single sheet / Maximum: 5/8 Inch.Triple Tab: Up to 18,000 pieces per hour.Double Tab: Up to 24,000 pieces per hour.Single Tab: Up to 30,000 pieces per hour.Production Rate:(based on 8.5 Inch (216 mm) length product).The tabbing system can easily be broken up into two fully functional independent tabbers with the removal of two integration brackets and cables. Modified base output and input sections to allow close spacing of bases. Updated head control firmware to allow close tab spacing with the required double tabbing on the leading edge Integrated base controls so one base "follows" the other Tighter registration wheel assembly spacing for improved product control The Ameritek Jet1 design has been updated for improved operation in tabbing booklets to accommodate the new tabbing regulations.Įxtended guides for enhanced product control The booklets must be run at 90 degrees when compared to the traditional folded self-mailer. The biggest difference, besides requiring two tabbing heads, is the orientation of the mail product in the tabbers. This requirement can be met through the use of an in-line dual headed tabber assembled out of two independent tabbers. The new booklet tabbing rules require two 1-1/2" tabs wrapped on the leading edge of the mail piece and one 1-1/2" tab wrapped on the trailing edge of the product. New USPS Tabbing Requirements and Solution In-line dual tabbing solution will accommodate the two tab / one tab requirement for the leading and trailing edges for automation compatible letter-sized booklet mail. Works in-line with inkjet addressing systems easily. Its superb design and engineering combined with Ameritek's first class support insures your company years of reliable production. Easy to set up and operate in-line or off-line with the highest productivity for today's mailing professionals. Meet all your requirements for tabbing, labeling, stamp or decal affixing with the Ameritek Jet1 Tabber. Rena Jet1 Mail Tabber Labeling Machine Mail Tabber / Labeler / Post-It Note Affixer / Stamp Affixer
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |